Tried sticking a serial buffer in between in hopes of convincing the compiler to allocate some extra memory, but it changed nothing so I took it out shot in the dark, but sometimes those work. Same cable. This cannot be undone. The Group moderators are responsible for maintaining their community and can address these issues.
Report to Groups. This includes: harm to minors, violence or threats, harassment or privacy invasion, impersonation or misrepresentation, fraud or phishing. Note: Your email address is included with the abuse report. Toggle navigation. Home Messages Hashtags. Search Cancel. Date Date 1 - 7 of 7 previous page next page.
HTH, Lincoln. Groups Links. You might want to try using Viewport and entering Passthrough mode to the appropriate com port, with the appropriate comm spec, and watching the Incoming line in Viewport to see if the transmission from the Ademco is actually correct.
Are you connecting to the PC with the same cable that is used to connect to Crestron? Are you sure you wish to delete this message from the message archives of crestron groups. Cancel Yes.
I chopped an old telephone cable in half and soldered the capacitors in place with alligator clips for the power and resistor as I was not sure which values I would need, the resistor could be soldered in place now that I know it works with my modem. I am just clamping on to the 12VDC panel power supply for power but you could use a 12V battery or wallwart.
Here are all the values I tested below and they all worked. If the two above options fail your modem is probably not going to work. This can be used in place of the above two options if you do not want to make your own cable. Make sure you do not buy a null-modem cables these are wired with the receive and transmit lines crossed for direct computer to computer connection. Let the fun begin, once you have all the equipment needed to connect to your panel you need to setup the Honeywell compass software.
The link to install guide is in section 2. Open the software and will get this screen. The next screen you will see is this, it is the main screen of the compass software. To make edits to a panels configuration or even connect to a panel you need to create a customer account for that panel. This software is designed for professionals to store the configurations of all the installations they have done.
You can leave most fields blank here, make sure the Account number is 4 digits. The panel and revision need to be set. The revision is the first number on the label attached to the PROM chip on the panel circuit board.
Once the account is created double click on it from the account list. The configuration show will be the default configuration as you have not retrieved uploaded the current configuration from the panel yet. Click the connection icon next to the save button and the below dialog will open up. This is used to connect to the panel and activate all panel configuration changes. Click the connect button. There is were you activate the connection to the panel. Click the connect button in the Honeywell compass software and the modem will connect to the panel.
See my video below for what this sequence looks like. The terminology can be confusing but an upload is where the panel sends data to the compass computer and the opposite logically follows; a download is a sending data from the compass computer to the panel. Directly into a laptop. Our old compass software crashed. I there any where you know of where we can get the original compass software. Any tips on finding the 2. I did not have that much luck finding the update file, the best bet would be to get it from someone or find an older version of the download document.
With some creative searching I was able to find an older version upgrade path that is hosted on the same site as all the other files. Below is a search that will find just the file I found. Hi, I need to program a Honeywell Vista 48LA panel and dont have the alphanumeric keyboard, just the standard keyboard.
Sometime ago I already connect a DSC panel with this solution…. Sorry my bad english. Dear Sirs, I have one request. After installing compass 2. How can I add this panel to its list.
The program I have tested the panel Vista and functions by mistake, but I desperately need your support for the Vista BPT you need to start installing. Thanks in advance!
Inquiry, I am not clear the connection of the capacitive cable … The capacitors of. Ie resistance and capacitor go in parallel between the cable cut red and green? I confuse the yellow loose crocodile clips and the loose green crocodile clip … On the other hand, do not feed the cable with positive and negatrivo of the panel as in the case of Watelco cable?
Thank you! I am trying to direct connect to a Vista BP panel and keep getting messages that say the port selected is in use. Keypads use 4 wires- two for DC power, two for a simple serial data bus. It works on all boards above the Vista20 full-sized boards — even old ones but only the latest boards the BPT series have the RS level shifters built in so no additional hardware is needed. A community for technical news and discussion of information security and closely related topics.
However, the pin is not saved, and there are no buttons directly on the dash like I see documented for the AD2USB plugin. Ask questions in our Discussion Threads. There was actually a post a while ago of exactly that if I recall, where most people said exactly that. True, but that depends on which hats you wear: Does that mean all the sensors are some industry standard stuff develoment would work with something different? Use of this site constitutes acceptance of our User Agreement and Privacy Policy.
For the testing environment, you are looking to emulate the binaries with QEMU or something else? I see there has been no activity in a while, so I would like to know current status of your plugin. Always link to the original source. I wish someone would reverse engineer my Gemini home security system. Q4 InfoSec Hiring Thread.
Even if the extension mattered, it could have been a totally proprietary one. Titles should provide context. In the longer term, Honeywell has a nice home automation interface board called the CBM which appears to solve all the issues associated with using the ECP bus.
0コメント